Artificial intelligent assistant

extruder

answer Answers

ProphetesAI is thinking...

MindMap

Sources

1
extruder
extruder (ɛkˈstruːdə(r)) [f. extrude v. + -er1.] 1. A machine that extrudes (see prec.).1959 Times (Suppl. Rubber Industry) 27 Apr. p. iv/6 Extruders can be of all sizes up to 15 in. in diameter. 1960 H. Powell Beginner's Bk. Pottery ii. 63 Extruder, a pressing machine for making clay coils. These m... Oxford English Dictionary
prophetes.ai 0.0 3.0 0.0
2
Liposome extruder
To drive this extruder, a compressed nitrogen cylinder is used. Multiple liposome extruder system A multiple liposome extruder system is fitted with pressure and temperature sensors and a control panel to regulate liposome wikipedia.org
en.wikipedia.org 0.0 1.5 0.0
3
Things tagged with "Extruder" - Thingiverse
Things tagged with ' extruder '. 0 Thing s found. Download files and build them with your 3D printer, laser cutter, or CNC. Thingiverse is a universe of things.
www.thingiverse.com 0.0 0.90000004 0.0
4
Skirt extruder ignored? – PrusaSlicer - Prusa Forum
1 day ago — ... skirt as a draft shield to prevent warping. In PrusaSlicer 2.7.4 I selected extruder 1 (ASA) for "Support material/raft/skirt extruder" and ...
forum.prusa3d.com 0.0 0.6 0.0
5
TMC Extruder Error | VORON Design
Apr 28, 2023TMC 'extruder' reports error: DRV_STATUS: 000f00e0 s2vsb=1 (ShortToSupply_B!) ola=1 (OpenLoad_A!) olb=1 (OpenLoad_B!) cs_actual=15. Since I built my own wiring harness instead of ordering off-the-shelf, I figured there was most likely a wiring issue. So I rechecked the steeper motor wiring from the toolhead (I have a 2-piece Hartk SB PCB) to ...
forum.vorondesign.com 0.0 0.6 0.0
6
Demaco extruder
The Demaco extruder is a pasta extruder built by Demaco in West Melbourne, Florida, United States. It is the first pasta extruder ever built for USDA sanitary food plants. wikipedia.org
en.wikipedia.org 0.0 0.3 0.0
7
Adding a Bowden extruder to a direct drive setup I currently have a single extruder (direct drive) Tronxy X8. I am thinking about adding a second extruder, that I would use only occasionally. I really like the charac...
I'm an amateur and I used dual extruder printers but never built any.
prophetes.ai 0.0 0.3 0.0
8
Lyman filament extruder
The Lyman filament extruder is a device for making 3-D printer filament suitable for use in 3-D printers like the RepRap. The goal in the competition was to build an open source filament extruder for less than $250 in components that can take ABS or PLA resin pellets, mix wikipedia.org
en.wikipedia.org 0.0 0.3 0.0
9
Extruder driver not working I have a geeetech g2s pro and when I request to print something, the extruder motor doesn't move (it is connected on the board), therefore, the printer prints some kind of imaginary object....
Found the solution, I had to swap the cables on the board, now they are working.
prophetes.ai 0.0 0.3 0.0
10
Stuck filament in the extruder of Infitary M508 **Model:** Infitary M508 **Details:** The filament is stuck in the extruder preheated for PLA (the filament is PLA 1.75 white). The extruder's motor works and the filam...
Unfortunately you're going to have to tear the extruder head apart and clean the nozzle. The only other solution is to replace the nozzle and extruder tube. The filament is stuck in either or both of these parts.
prophetes.ai 0.0 0.3 0.0
11
Dual extruder does support/secondary extruder stay hot during entire print? The hot end set-up for my printer consist of 2 Titan Aero extruders. The printer relies on Reprap firmware and a Duet 3 controller board. Whe...
use a standby temperature for the beginning of the print where supports are used, and manually change the G-code at the last change to disable the HIPS extruder
prophetes.ai 0.0 0.0 0.0
12
Marlin firmware question for dual extruder I've recently added a second hotend and extruder assembly to my 3D printer and I've made all the necessary changes in the firmware. I've defined the temp sensor for hotend 2,...
`Extruder` refers to the active extruder, the loaded/active tool. Based on the active extruder the `Extruder` controls either your `Extruder E1` (this is known in the firmware as `Extruder E0`!)
prophetes.ai 0.0 0.0 0.0
13
Micro extruder parameters Std. Antpedia - 分析测试百科网
国家建筑材料工业局, Micro extruder parameters. JC 343.1-1991 Vacuum brick extrusion machine type and basic parameters; Professional Standard - Machinery, Micro extruder parameters. JB/T 2707-1999 Shockless jolt squeeze moulding machine Types and basic parameters; JB/T 2707-2015 Microseismic compactor type and basic parameters
www.antpedia.com 0.0 0.0 0.0
14
Anet A8 Installing second extruder without changing board I am wondering if it is possible and safe to add a second extruder to my Anet A8 without changing the main board. I was thinking splitting my Z motor wires to ...
The Anet A8 board has 4 integrated (A4988) stepper drivers, one for X, one for Y, one for Z and one for E (extruder 0). !
prophetes.ai 0.0 0.0 0.0
15
Creality 3D Ender-4, a "extruder kit" does not fit the frame This is my first time building a 3D printer (a "Creality Ender-4"). Everything is going fine except the "extruder kit" part that does not have enough space...
realized I'd have to void the warranty just to finish putting together my printer but I wound up boring out the holes a bit closer to the edges of the extruder
prophetes.ai 0.0 0.0 0.0