so mean SGR 1500 how dramatically from a concrete we almost always recommend to do a test because there are so many ghouls in the market that is difficult to determine if our material is going to remove every deal plus there so we always recommend a test here is a list of the items that you will need to do a test on your floor and then also a list of every salt from the application alliterative are looking for select a small area one area where they're heavy glue apply about a 2x2 square foot area apply the material let it sit there for 12 min 12 hours and after 12 hours come back and give it dry apply a little more material make it wet and then give it about five minutes and then scraping if all the glue comes off at that point in time then you have a good positive test which means that you can do your project quite easily removing the glue that is in your floor here's the list of the items you will need to do the large project you planning and preparing and the job site it's also important that you prepare just that ahead of time and planned we always place cardboard if I saw the door of the projects well because shoes can be wiped on and that track the product all over the place we also figure out the way to exit easiest way to exit from the project as you notice and maybe steps to curl go up and then in access to go outside where you need to wash your tools and everything else the product is environmentally safe so it could be washed the drain or with no issues behind it the second part to look at is also you have to make sure the product is very thin and it runs and if the first not level it will all the possible tend to go one direction so we always create a small one-inch barrier of absorbent at each door so that way the product doesn't go outside the project area that we're trying to treat applying the fielding SGR 1500 remover here's the method that we love to follow that makes it easy to apply and then prevents from splashing and getting the area too messy we use a 9-inch very thick natural at least an inch thick and now and then we slowly apply it you want to apply it richly into the floor so that way it has time to sit there for 12 hours and not dry and penetrate through the blue now some glues maybe 6 or might be sent so you want to make sure you put a nice thick coat of the material on top of it as you can see we try to avoid walking on it simply because a material it is tracked very easily and also creates a slippery surface so be careful as you apply this and if you have to walk on it be careful when you walk on top of it as well this is a soy-based product which totally environmentally safe so there is no issues there's no smell there's no BOC so we could be working in this office as well as people working in the office next to us and there will be no smoke affecting them the probable remain in place for at least 12 hours you after 12 hours a path or today we come back and you will notice that in the in the video that the center of the room is higher so therefore most of the remove it has rolled down to the edges of the room you can see where has patil that means the old lighter areas are clean but wherever patil it dry it out so what we do is we do a really quick light treatment over it and let it remain there for about 10-15 minutes so that way a reenergize --is the blue remover and it's easier for us to scrape it off as you can see just rolling at a quick pace of the holes work just enough to get the floor wet we can come back later on and then scrape it try to make the Java sufficient as possible so therefore by reapplying a little more material it makes it easier to remove the glue of the floor you removing and collecting the glue if you need to walk on that web product sometimes we use what we called spikes use their shoes with little spikes on the bottom and those allows us to walk on the floor without getting a shirts dirty we usually don't use them because the floor it is slippery and sometimes it's difficult to walk on them so therefore what we do is we try to use some as little as possible but they're very effective if you have to walk on a wet floor and that issue is dirty the next step is we get a trash can with a liner in it so it's easier to dispose the material as we collect it we start by using the scraper or I spatula sometimes people like use the squeegee we like to use the scraper because it's a little bit stiffer than the squeegee and it does conform better to the surface of the concrete so therefore it picks more of the glue and Lisa - passes through it as you can see we're collecting the glue here and as we collect the glue we are spreading the absorbent the absorbent is designed for two purposes one is to reduce the puddles and collect the liquid and two is to prevent us from spreading a splashing on the wall as we collect the material in the floor as you can see he creates a small blick wa T area and then he moves the absorbent to that area the absorber starts serving the material and eliminating having a lot of this material running all over the place you also notice that we work from the door into the room and therefore we don't have to step on the material that is wet at the present time and allows us to clean other material a lot faster more efficient one of the most challenging areas and this jobs are removing the glue off the edges near the wall two reasons in this case on this job we have to be careful not to damage the freshly painted walls so therefore we try to keep any splashing or any material off the walls and when we work near the wall typically they're the ones that require most attention we will use another scraping tool for that which you'll see later in the video but as you can see here we apply the absorbent as we collect the material puddles and then we just basically moving around until we create a nice Mountain or material absorb and we can collect all this material and then dispose of it rather easily as you can see in the video you will see also notice that there's still some areas on the floor that look dark those areas still have a glow and and what happens is that the floor is not perfectly even so you're going to have some peaks on the floor in some valleys even though they're not this will officially available to us this still there and that's what the dark areas are so therefore they're going to require a little bit more treating in those areas so first we also reapply a little more around the edges because as I mentioned before they're the ones are more challenging and any main big spot in the middle that flow we quickly just touch it up with the material so it has an opportunity to work a little more into it in that area usually a 5-10 minute application that's all it really requires and then we get the product off the wall we will follow after we do that with a little scraper hand scraper that we have to remove the edges anything that might be in the edge that we cannot reach with a large spatula allows us to get very close to the wall without any damage and square those areas that may need a little more attention we will follow the complete edge of the wall just to make sure that everything gets cleaned up as this as possible you notice that the center spot already melting so therefore they read to wash washing the floor the first thing that we do when we wash the floor is to mix the seal Green oil cleaner degreaser that comes with a product we use this as I mentioned before is a soy-based product it does leave an oily base on top of the floor may be slippery and also we want to make sure that that oily surface is completely removed so that whatever the following tips that we're going to be doing with this floor will not fail at this point in time what we do is we mix it we shall pour everything into the bucket fill up the five gallon bucket the product comes in different sizes you may need different size containers we use a mop just to apply the material so we don't need to do that and then we in this skate you're watching us using the scrub brush it's a stiff bristle scrub brush just to try to remove whatever things are there that may be a little tight in the floor this helps us do that this is one method of doing it we also will be showing you here in the video the other method to do it if you want to do floors a little faster or you have such machine but it's a scrub brush will also work as well in doing the final wash once you press it a little bit we apply water from the whole clean water from the hose we always try to mist it so that way we don't have a lot of water just enough to collect and then we follow the shop back as you can see as he shot back to the floor it is collecting all the dirt blew and everything else all at once a lot of our customers like to do a second just clean water job which means they just basically after you clean up all this you come back and you spray just clean water shut back it up and that will make sure that your floor has nothing left on it of impurities to prevent you from doing your next flooring here's the other example that we use we use a sealed green diamond pad it's a pad that scrubs the floor it has impregnated diamonds so it really gives it a good scrub to the floor and removes whatever is there in the floor is not designed to remove the blue is designed to scrub the floor well as you can see he is preparing the device called the floor maintainer that applies the oil cleaner degreaser just enough to get a wet a heavy wet is better this machines the way to the floor the better they were and then he just goes ahead and start scrubbing the floor in a simple motion not too fast not too slow just enough to give it a good scrub to the floor in that area a lot of that professionals which is what they use to get a little more efficiency in cleaning the floor homeowners also some of them use this too as well because they don't want to smell that I'm brushing it is an option if you're doing very large floors highly recommend to use a scrub pad with a diamond and a machine they do give you a lot of square footage rather quickly with very little effort we follow by spraying a little water on the floor and then we immediately shot back and you can see there how clean the floor is getting at that point in time a lot of times up for it slip at that area and now you have remove all the glue from the floor completely and a lot of time so sick a second wash just takes place just to make sure that the floor is perfectly clean then we allow the floor to dry you Drive floor and final touch is dry we can we follow again the floor and make sure it with the skin scrapers now there is no items that are left behind sometimes just a little touch of sheer and they're mostly next to the wall where the most challenging part of the job typically is so we go around and just scrape them up and then sweep them off the floor and then the floor has been basically completed we allow the floor than to dry it's also important to know that you have several options you can do with this floor after the floor is dry as you can see in the picture this is a two hour drive floor a lot of character on the floor a lot of stains are there this is a 70-year concrete floor with a tile pattern that's embedded in the concrete which is really nearly impossible to remove off even if you go under for quite deeply so here you can see what the floor looks like a couple hours drive some of the options that you have from us is that once your first nice and clean you can come back and stain it with a transparent color stain it's a water-based stain safe to use and then leverage the pattern tile that you have on the floor as well as some of the stains and give it that antique floor with a lot of character this is very commonly done at seorim we have a 36 different colors that you can use to create a beautiful floor this quantum will be followed by couple coats of sealer and a shine gloss so you want to be very glossy for more information on this project or questions about how do the project or on the product materials and for the items please call us at 899 seven three eight seven three eight hundred nine and seven three eight seven three or visit our website at Co green - ciao