I hope you're ready for a challenge because this one is all guaranteed to be lots of fun this is going to be a dagger but it's going to have an actual flat blade more like an actual dagger I've got a 160 I've blown up a little more than halfway I've got a black 260 here for the handle that I've blown up also a little more than halfway we're not game is all of it and then I've got a gray 360 that I have reverse inflated there's the nozzle and with a nod to about eight or nine inches and that's where the fun is going to come in so we're gonna start by making a handle and you can make whatever handle you want if there's another handle that up and one of the others that I've made you can do that I'm gonna make this simple short short handle so I'm gonna move kind of quickly through this part bubble para pinch twist looks like I've already shown you this if you haven't watched that you can go back and watch it get more on it if guys don't care a pinch twist handle another pinch twist and then our two pieces will stick out to the side here not real big I'm gonna make them shorter for the dagger that into the sport and put a little bubble pinch twist and another bubble same size as the other one make your first extension on one side of your hand plug is what that is and then we're going to repeat the process on the other side just like that security in place and then we're going to pop yet this off let me hear that it again and again you can use whatever handle you like cut adapter if there's another handle this is whether you to do that and there's a quick little handle that I've made we're gonna set that aside now is where the real fun begins we're going to take our 160 and we're gonna fold it in half and I actually want this to be a little shorter I'm gonna shorten it out there's about when it's folded that's about eight or nine inches that's about what you want someone to put a twist there and let the excess air out of that and then I'm gonna tie these two in together what you essentially one is a little loop then I've got this a little loop like that that however the ones of your dagger you will however long you want it to be but the trick to this is you want to make sure it's gonna be no longer than 1/3 to 1/4 or so the length I would inflate it 364 350 whichever you will be using because what we're gonna do is double stuck this inside of this if you've seen the tongue technique this is the same thing now we're going to take this and fold it in half I'm going to start with the rounded in here you can start reading but I just like to do this book of this book it's at the other end personal preference now we're gonna take our folded 160 and start pushing it into the end of our 360 I'm going to lay it on the table here and sort of force it in normally want to do this I would push it against my body but then you couldn't see it very good so if I lay it on the table you can sort of see how I'm creeping that you're forcing that up inside there so we're on station minion and then when we do this you're gonna have to make sure you hang on to over here if you in my left hand a of them so if I let go otherwise I don't want to pop my couch just work it you want to get it completely now I've got my finger you can see where I've got my finger pushed in and if you look very faintly you can see the silhouette of the other blowing in there now what I need to do is pop this outer piece and I'm just gonna cut it in there so you end up with that they're a giant swollen finger then pull your finger back out now I'm gonna take it I'm gonna trim this really close to the end here you can't see it very well but there's the end well if you can see me you're rolling that backing out then I'm going to take and where I've trimmed that I'm going to just roll that back once you get it started and you can just roll it all the way back along there till you get to the end and you really don't have to do much else I'm gonna squeeze that end a little bit and what you end up with you can see how it's now flat from the side but it's got width that way a few so I've got wrinkles when you roll that back it forms a strange little nozzle I put a little puff of air in there and then I can push it up the end and I'll get those wrinkles out and then I just need to trim the end of this we don't need to re-inflate that at all because you wanted to stay flat like that to make your blade and you just take this in and flip it into the tube pinch twist there on your handle and presto you've got a little dagger with an actually flat dagger white plate