hey guys today i'm going to show you how to disassemble and reassemble a rubik's cube i'm going to be using my stickerless one so i can find the pieces easier that i need to find but you know you may have a rubik's brand you may have a speed one i'm also going to explain how to take apart cubes like the dye and panchi that have torpedoes in them or a torpedic effect like the feng shui sweating around has a really big torpedic effect and if you have it really tight it's actually impossible to get it out so if you have a fangshing wren you can start by popping off this top center taking a screwdriver and unscrewing it slightly then it'll become kind of similar to one of those other ones so there's two different ways you can do this you can put pull down on this this layer so you can get your thumb in there and pop this out on the guhong it's very easy and then you can do the same to these corners whoop and then you can either turn it a bunch and just let it crumble basically or you can do it like this turn this layer 45 degrees and turn this layer slightly and just keep it keep turning this layer and take the pieces out one by one and then you can do another layer this would be good if you were wanting to sort the pieces a specific way and so that you that they're not all over the place but you know just keep doing that until you have all the pieces out so now set all the pieces to the side if you're using a torpedo cube you can't just do that you have to twist kind of like that to get it out rubik's brand this is a rubik's brand it's the same and to put it back together you need to find one of your white edge pieces and basically zoom in a little here you get the two centers that is going to be in between turn put the white one here and the other one right here turn the other one 45 degrees put this in here like that and then turn it back like that turn it like this find the piece that's going to go there the white green piece and do the same exact same thing set it down on the table and then get the corner piece that's going to be in between all these is this one and then kind of if it's a dying cube put it first like this and then like that if it's a rubik's you can just drop it in and then on rubik's you're going to want to turn this like this you're going to want to get the piece that's going to go there in this case it's red green and turn this 45 degrees and then just put it in there if you have a dying cube like mine you can just pop it pop it in and there you go you have that then basically do the same thing on this one that you did for the other one like that and then do the same thing here that you did for the other sides and then on this one it's going to be a little bit different you can't just put it in like that so just act like this red center or whatever center is right there is going to be your white and put it there and then simply rotate it down to there then get a white corner it could actually be either one but just stick it in there and then do that and on the very last one just put the corner in don't put the edge in because then it'll be easier to put the top layer so just get any edge any of your remaining edges make sure it has yellow in it make sure it's not like this like this one doesn't have yellow in it or whatever your top center is and just put it on there like that then get another one and a corner make sure it is yellow and whatever this color is so whatever those two colors are make sure it is in this case it's yellow green so i'll put this there now if it's this one this one is yellow green too but if you put it in it doesn't match up so get the other one put it in now what's on the other side of that oranges so get your yellow orange edge and just keep doing that orange on the side get your orange corner put it in that one's blue get your yellow blue edge then turn it again blue corner like that now just turn it like this and then get this one the only corner you have left just stick it in and the only edge you have left or not the only but the only yellow edge you have left put this like this turn this back turn this 45 degrees and put in your last edge similarly to when you took it out and you can just turn that layer until it's solved and the reason you need to put it back together solved is because if you don't you may get when solving it you may get a case like this where it's flipped so anyways that has been how to disassemble and reassemble a rubik's cube thanks for watching i will see you on my next video